Search results

I spent multiple days talking to ELK about my problems with counters.  I even bought a new M1G after they said it must be a hardware problem with my 7 year old M1.  This was with firmware 5.3.10.  I never had a problem with 5.2.10 but had to upgrade when i got a new ethernet module.   The new...

I have one in the exact situation you have.  900 foot uphill.  I found that I had to place the receiver on an outside wall (receiver is inside).  When it was in my wiring closet, it was not 100% reliable. 

Thanks.    They connect to 3 separate zones on an M1 gold for the panel.  I'll have to look at the current draw to see if I can support the additional power.    There are 5 detectors on 2 zones, and 6 on another.   So if the detectors are 35 mAmp during  alarm, will all the ones on the zone go...

Which system Sensor would you recommend?

Thanks.  What's a good replacement for these?    I'd rather not have batteries as 4 of these are in 20 foot plus ceilings.  They are connected to an ELK m1 gold with 3 separate zones - upstairs, main floor, lower floor.   Thanks

I have 16 ESL-541C smoke detectors which are all about 15 years old.   Do I have to replace the detectors, or can I just replace the chamber using this on amazon (or elsewhere somewhat cheaper)?   http://www.amazon.com/GE-211-10PKG-Replaceable-ESL-Detectors/dp/B003XZVHOW/   Thanks!   If the URL...

The PS "+" and "-" is an input from your litetouch power supply, the SW "+", "-", and "D" are the 3 wires that run too al the switches (getting the power from the power supply).

Are you going to have the Arduino use the same 4 wires?    I was looking at just replacing the switches with something else that talks with a PC and the PC sends commands to the litetouch LC5000 controller to control modules / groups, but I didn't find anything cheap enough that supports a...

What specific 485 adapters are you using on your PC?  I'd like to play with this connected to a jandy system and see if I can crack the protocol.  Also, is there any documentation on figuring out baud rates and settings?   Thanks.

Can you get and set the clock?  If you can, then your cable works.   A new Savant controller should be around $3k, but you should be able to find controllers on ebay for around $800.  Unfortunately, those may have their own set of problems.   I heard a rumor that Savant has sold Liteware to...

If you have a gas pool heater indoors, you should make sure you have CO detectors - especially if the pool access is directly connected to the house.

Try heston technical in kirkland and see if they will do it on a time and materials basis. As they are not an elk dealer, you'll have to supply the m1 and boards. http://hestontech.com

Doesn't work for me, which is typical of the elk ethernet products.

You discover the M1 sends lots of arm / disarm command and keypad commands which make no sense.

I have all my speaker cables and control cables (cat-5) run to the same location as my security system. It gives you a bit more flexibility as you can put multiple amps / receivers and balance loads from a single location.

The Pioneer listed in this thread is a pretty good receiver: http://cocoontech.com/forums/topic/22061-recommend-51-or-71-receivers-with-ip-or-serial-control/

Give them a phone call or send an email (phone call works quickest). They'll be able to give you dates on availablity of announced products.

Some boilers need to be set at a constant level, like 175 degrees F, to avoid condensation and othe issues.

I have two MC-66's that I'm using. The Lync keypads require double size boxes and I only had single size boxes to put keypads in, so no Lync for me. I'm running 20 zones (one 12-channel amp, three 8-channel amps, and one 5-channel amp) and using the RS-232 inputs to control them as a 12-zone...

read this post http://cocoontech.com/forums/topic/14635-elk-m1-databus-errors/page__hl__databus+ohms__fromsearch__1