Search results

Last week, when I updated my automation program with a new block, I checked off all but the Extended box, and hit send and then looked away. About 2 seconds later. I looked back and I was expecting to see it deleting the old program but it said, I believe “Waiting”. I had never seen that...

My previous post dealt with network problems I had trying to connect to my OmniPro II, which I was finally able to get it to do with the help of forum members that stuck with me for a few days. But now, since remedying the network connect problem, when the system came up on reboot, the two...

Comm Status: Reset by Peer (10054) So I reboot my main router, Arris (which is basically the modem) my cascaded Linksys (which was done so we would not have to change everything when switching from DSL to Fiber), the Omni Pro II and two computers. Comm Status: Retry (100) came up several...

Now that CES has come and gone, it seems that MATTER is running full steam ahead with their protocol. Does anyone know if anyone is writing a MATTER interface for HAI OmniPRO II? If not, it would seem that the Omni may be follow the way of the dinosaurs:(! Just Curious. Thanks.

I am hoping that someone may know how to remedy this problem my outdoor keypad is exhibiting. The LED does not change to RED when the OP II is armed. Therefore, it is constantly showing with a GREEN LED. I have not changed any wiring since its installation 16 years ago.   Any ideas as to what I...

Hello - My OP II was installed 20 years ago, and UpStart was not even around. The way the UPB Lamp Modules were configured was with the OmniTouch 1st generation panels. You would hit the reset button five times on the module and it would blink blue for five minutes, giving the installer plenty...

I have had my Omni Pro II since 2004 and it has worked flawlessly and dependably. Now the peripherals are starting to go. When I renovated, I put outside floods lights on strategic peaks of the house to light up all around, for various reasons. I put the switches, for the floods, in the garage...

Last night we had the loudest, brightest, wettest and perhaps longest, thunderstorm I have witnessed while living here, in South Florida, for 30 years. Perhaps, I think it is all that, because a lightening bolt hit so close I thought it came through the vaulted living room roof, as next, I heard...

I installed my OPII during  the 2003-04 timeframe. I used different lighting protocols,( UPB, ALC, ZigBee) depending what and where the appropriate wiring existed, or did not exist,  in a house built in 1957 of cinder-block, poured concrete and stucco...in Florida. It is a fortress, which comes...

Does anyone know if there is a current cell phone interface for the OPII? I guess it would have to be something other than the Leviton  70A00-2, which was a G2 product.   Thanks,   Jim

HelIo -    I have ROM 3.11D in my OPII and I am wondering if there has been any improvement in the available alert sounds offered for "Voices". It's really only a cosmetic thing, but a few alert sounds, other than those "beep"s would certainly bring a little uniqueness and class to an otherwise...

First of all, I bet that headline caught your attention. I am about ready to turn off this automatic spell checker and thing that thinks it knows what you are going to say. Unfortunately, I can't see where you edit the headline but it was suppose to say "HAI's"!   Anyway, after about 8 years, I...

I am going to be adding ZigBee to my system as I may be the easiest way to replace an ALC switch that I have on separate branch of the house. Problem is, I am having a difficult time finding where they are sold. I have been to the ZigBee certification site but it seems they link to manufacturers...

I have an OmniPro II with about 5 ALC Lights on it covering the outside perimeter of my house. They all work fine from the switches, but do not work from the controller (Touch pads, iPhone, iPad, PCAccess). I thought it was a "no brainer" and got a new ALC board. Installed that and same thing...

I have an OmniPro II with about 5 ALC Lights on them covering the outside perimeter of my house. They all work fine from the switches, but do not work from the controller (Touch pads, iPhone, iPad, PCAccess). I thought it was a "no brainer" and got a new ALC board. Installed that and same...

Have tried doing this several times but unsuccessful, in programming my OmniPro II. I have fans and lights that operate according to room occupancy. However, I am trying to over-ride the motion to shut a fan or light off temporarily. I am including lines: WHEN lrflag ON THEN BYPASS ZONE living...