Search results

I just noticed a week ago that the LCD dislay is always lit on both my HAI control pannels. According to everithing I have read here and other web sites, the display is supposed to turn off in 3 minutes or so after last activity. That is not the case with mine. What could be causing them to...

I have the zwave kwikset hooked to my HAI. I can see the status on PCAccess when the lock is opened or closed. I want a code to auto lock the door one minute after the lock is opened. The lock comes with a default 30 seconds auto relock and that is not long enough for me to walk to the...

What is the best way or equipment to distribute infra red connectors trough the house to control tv's and stuff back in the media room?

I am unable to program my devices, when i try to program them I get the "no module in setup" message. I was able to program my devices before, I purchased a second 60A00-1 so that I did not have to share one with HAI and CQC. I did a reset on my switch but it is still not seeing the devices...

I purchased these units and wanted to know if they are truly no video loss and if they work as good as running a cable directly to the tv. I plugged them in yesterday and maybe it is me but i thought that the image use not as crisp. The alternative is running cables, which will be cheaper but...

Ok I ran cables for all my speakers from the closet to the livingroom. I used a monoprice wall plate http://www.monoprice.com/products/product....=1&format=2 What is the best way to connect these? I think I read that if you screw them on to the plate they eventually work themselves loose...

I about to start installing my ceiling speakers, I purchased monoprice speakers for my audio distribution. I would like to know if anyone has pictures or helpful guides on placement of the speakers. Also I have seen many members make their own boxes, does anyone sells already made boxes? One...

I want a light to come one after dark if the back door is opened, I also want this light to go off 3 minutes later. However If I am entertaining and the light is already on then I do not want this rule to apply. This is the way I have done it so far and it has not worked; 18. WHEN Formal...

What type of zone is it under pc access?

What is the best way to tackle this? I have a friend, professional AC guy that will do the connections for me and rework my AC ducks, but I am not sure how the dampers are integrated. Do they get wired directly to the panel? What type dampers should I get?

I been looking diagrams of the omnistat2 and it shows that the remote sensor "such as the ones I bought" 23A00-1 are wired directly to the omnistat2. Can this sensors be wired to the Omnipro II? If they are wired to the omnipro could I control the dampers based on the temp reading etc from...

Can I use a cat6 cable to wire the omnistat to the Hai Panel? I have two free cables in the location where i want to install the thermostat, but I can run a 4 cable 18 or 22 gauge if need be, the only reaon I am hesitating is because I already sealed and patched the whole on this location.

Is there a way to have the green light turn off, when the zones are not ready? I am visual guy and if I see at a distance that the light is not on, then I know something is open. Also while we are on the subject, I have a panel that is by a glass door. Is there a way to disable the lights on...

While reading about diff cat 6 cables I realize that I just got done wiring my house with this cable from monoprice Cat 6 UTP Stranded, In-Wall Rated (CM), 400MHz 24AWG 1000FT Bulk Cable - Black. For what I been reading maybe I should have used solid cable. Will this be a problem, will I need...

I started to work on my HAI alarm, prior to HAI I had a Ademco 21ip; the way the wire was set up, it used 7 zones on the pannel. I imagine that each contact in my house has an individual cable and they simply spliced two or three contacts into one zone to make it for example master bedroom. Am...

I thought that motion sensors only needed four wires. Could someone please tell me where my four wires go to from the HAI omni pro to this particular sensor? Also should I use cat6 cable? I bought originally 18gauge cable that I was gonna use for the sensors...

Not sure about what I need but let me tell you whayt I would like to do. I would like to be able to watch the movies on my computer "windows xp" trough the house. I was thinking about using CQC and touch panels to control everything. I have plenty of cat 6 cables to each tv "5" total and...

The HAI have a setting that allows you to set the switch dim-able or non dim-able in upstart. I did not see that option in the US2-40, but the web site says that it could be set either way. How do I turn dimmer off? Thanks

I installed cqc but have not gotten a chance to play with it. I as hoping that out of the box I would get a nice gui that would allow me to control my hai pannel. Does anyone has a step by step cqc cheat sheet?

I been changing switches through my house, this is the first single gang box that I have to change. After taking the switch apart that controls the formal living room light, I come to find out that there is no neutral wire. What should I do? It is a single gang box and it only has two wires...