Search results

I have 2 Omni Pro II consoles. One labeled HAI and the other labeled Leviton. The HAI labeled panel has buttons that light up with they are pushed and then go off after a period of time. The Leviton labeled panel has buttons that are light up all the time, they never go off. Is there any way...

I just noticed that HAI has released PC access 3.11.4.691 and firmware 3.11D but I did not see any info in the release notes.  Can HAI supply some info on what has changed/new in this release?   Thanks,

I just saw a press release from HAI by Leviton:  "HAI by Leviton Announces Yale Real Living™ as Latest Connectivity Partner"   In the release it mentions firmware version 3.14 or later.  Last I saw the firmware was 3.11c.   Is firmware version 3.14 a new version that is going to be released?  If...

Can anyone tell me (preferrably from HAI) if the HAI 14A00-8 remote temperature probe is still a current product or is it being discontinued? If discontinued is there a replacement or recommended alternative? Thanks,

I have a ceramic tile floor that is heated by hot water. Currently, I have only manual control, I would like to automate and also have 2 zone for the heated ceramic floor. 1) Are there any temperature sensors for the HAI Omni Pro II that can fit down a 1/2 pipe? 2) Are there systems that...

I have connected 2 Yale deadbolt locks to my HAI OmniPro II using z-wave and though I would describe my integration of the Yale locks and see if anyone had other ideas. The integration includes locking, unlocking, indirect integration into security zone and keeping track of 2 locks. Also...

Has anyone heard if the Yale zwave locks are available yet? If not when? Thanks

I have been looking at driveway sensors Cartell and Sure Action. The Cartell states that the sensor should be 35 feet from the street for traffic less then 35 mph. Cartell also has a sensor that can be within 10 feet. I would like to put the sensor as close to the street as possible. I will...

Can you add more then 2 speakers to the "Two-way voice Module #10A11-1"? I would like to add 2 more speakers without having to add a whole house audio system. I can not justify the $$ for a whole house audio system that would cover 4 rooms. Any help or suggestions would be appreciated.

Is it possible to download a trial version of HAI wl3? I currently have an OmniPro II and I would like some type of remote software. I would also be trying it on both the current version of Microsoft Home server and on the RC version of the next version of Home server. I have already tried...

I would like to know which models of the Carrier Infinity thermostats does HAI support with the OmniPro II? I have a carrier heat pump with propane as the backup. My current thermostat is an Infinity but I'm pretty sure it can not be controlled. Thanks for any info.

I have an OmniPro II with a Leviton VRCOP for controlling my Leviton Vizia RF+ switches. I have written the following simple program: 1. WHEN Laundry ON THEN Mud Room Light ON When I turn on the Laundry light it takes 5+ seconds before the Mud Room light comes on. This seems a bit long...

I have Verizon fios for my phone service. Therefore, I have fiber coming to the side of my house which provides broadband, tv and phone services. Do I still need a phone surge arrestor on the telephone line?

The more I read the more confused I get about motion detectors. Is there a good review of motion detectors? How about a tutorial? I am trying to figure out how to compare the detection capabilities of different motion detectors especially when approaching head on. Any comments or info? Any...

I am planning on installing a HAI OmniPro II (20A00-8) in a Leviton series 280 (28in.) structured media can. I also plan on installing 120 volt recepticle in the bottom of the Leviton can for power and X10 PIM. 1) Is the OmniPro II 20A00-8 UL listed? 2) Do you see any problems with having...

I am in the planning stages of implementing an HAI OmniPro II. I am researching Dual mode motion detectors. I would like to know if the motion detectors are always powered on or are the only on when armed? The reason for the question has to do with the dual mode. I'm not sure I care to be...

I am in the planning stages of implementing an HAI OmniPro II. I have been researching motion detectors and becoming totally confused. So, any help would be great. I will need both indoor and outdoor motion detectors. I prefer to use wired technology when ever possible but I have locations...

I am trying to understand what the advantages or disadvantages there are between using the HAI wireless or GE Interlogix/Caddx for security. I will be purchasing an OMNI PRO II. I appears that the HAI wireless interface for one is less expensive. Any other comments between which one to use...

I would like to verify that the 83A00 Power Hub is an additional power supply that you need if you have lots of devices? The Power Hub does not replace the need for a separate power supply to power the OmniPro II controller. Is this correct? If you're wondering I have an x-10 controller...

I'm trying to find more information on ELK-M1XZW and how it controls Leviton z-wave devices? Does it support bi-directional communication? Can the ELK-M1XZW enroll z-wave devices or is another controller needed? Does ELK work with ControlThink? Thanks,