Search results

OK folks, I've seen (and been following) the many threads covering cellular communicators spawned in the wake of the 2G sunset.  I am finally ready to pull the trigger, but am having some trouble deciding which way to go.  I've searched extensively here (and elsewhere) without finding the...

I have been using an HAI ZIM in conjunction with my OPII for the past year with no problems but, for the past month, the OPII seems unable to communicate with my ZIM and, thus, unable to connect with my 2 Zigbee Omnistats, Load Control Modules, and Yale Zigbee Deadbolt Locks.   Again, this setup...

Title says it all, I have an HAI Omnipro II system with 42A00-2 wireless receiver and a number of GE wireless sensors.  One or two zones (furthest from the receiver) occasionally report trouble or not ready, hence the repeater.   Unfortunately, the documentation that accompanied the repeater is...

I'm wiring in some ATW Doberman Plus siren/strobe units (with tamper switches) to my HAI OP2, and want to confirm the wiring.   My understanding is that i should wire as follows (OP2 ---> ATW): Horn GND -> Common (BLACK) Horn EXT -> Positive (strobe & siren) (RED) Zone +/- -> (non-polarized)...

Hi- i recently upgraded my OPII from 3.11D to 3.12, and have been having significantly reliability problems with my GE Wireless sensors since then.   The problems started immediately after the upgrade: after the controller restarted, it immediately reported that all my GE wireless sensors were...

Hello all, I'm about to move to a new (well, new-to-me) home, where I'll have to start nearly from scratch on security, whole house audio, lighting control, home automation, surveillance, irrigation, etc.  In my current home, I have an HAI OP2, UPB lighting, Nuvo Grand Concerto, Rain8UPB, IP...

is there a URL scheme available to set a flag to a specific value using HaikuHelper? in this case I'm looking to set a numeric value for temperature.

I like the idea of the RainAdvisory flag used by HaikuHelper and i've updated my HAI's sprinkler automation rules to consult that weather forecast information. i had originally planned to install a rain sensor which would also interrupt sprinkler schedules for a few days following a rain...

I'm looking for the best way to reliably archive the event logs from my OP2. i had posted a similar question back in December and lupinglade suggested using HH. i recently got a machine set up w/ HH for this purpose, but haven't got the event logging up and running. my request for help in...

I finally got a machine set up with Mac OS 10.7 (10.7.3) and installed HaikuHelper. Unfortunately, after completing the setup and instructing it to sync, it promptly crashes with an uncaught NSRangeException. Here is a snippet from the crash report: Process: HaikuHelper [565]...

CT seems like the right crowd to get the sort of input I'm looking for, but I couldn't find a more appropriate section than 'Wiring Closet' to ask this. long story short: i have an attached 2 car garage that has an insulated rollup door, dual-pane window, and is fiberglass insulated (ceiling...

I'm interested in keeping my event logs long-term. What's the easiest (to setup and maintain) way to manage this? It looks like it would be relatively straightforward to use the SDK to download event log lines, but I'm wondering if someone has already done the work, or if WL3 or somesuch...

my omnistat2 sits in a hallway outside our bedrooms. when all the doors are closed and the heat is running, the temperature read by the thermostat can be 4-5 degrees off of that in the bedroom. i'm experimenting with the Heat anticipator settings on my omnistat but i'm also planning to install...

i replaced the switches in my hall bathroom which control the built-in light, nightlight, fan, and heater of my exhaust fan with a pair of SA US22-40 (dual dimmer w/ changeable faceplate) UPB switches, each with a double switch faceplate. i configured the switches to disable dimming (i assume...

I just installed my C3 into my existing HAI OP2 setup and i seem to be having some trouble getting everything to work as expected. I have inserted the C3 inline into my existing telephone setup, with the C3 now sitting between the voice jack on my cable modem (comcast digital voice) and the...

Right now I have a 10A11-1 (Rev C IIRC) two way voice board and 33A00-4 Alarm Console w/ Speaker and Mic. spoken messages from my OPII are output there. I also have an 8 zone NuVo GC whole house audio setup, and i was planning on using NuVo's source 6 as a paging channel. I currently have...

(oops hit submit too soon) Just got these items on Friday and have had the weekend to play around with them. first off a few quick notes about the 10P: the 10P runs XP embedded, and the image isn't locked down, so you can install additional apps (e.g. PC Access or other windows apps) if they...

While I was doing some testing of my AlarmRelay monitoring setup, I powered down the panel, removed the sounder wires, and powered it back on. I forgot that I had left the 'supervise sounder' settings on. The message that was reported on the console, omnitouch, and logs was "FIRE TAMPER...

This isn't exactly a continuation of the previous discussion around HAI OP II / NuVo GC integration issues so I'm putting this in a new thread. I've just recently added a NuVo MusicPort to the mix. I've got the MP software (actually Autonomic MCS-EX 2.0) installed on a Vista Home Premium...

Just had a strange occurrence that I can't explain.. I was testing my HAI/NuVo GC integration (for bkgd, see this thread) through my Omnitouch 5.7, browsing my Ipod metadata, trying to select "Artists". It wasn't responding, so I touched it a few more times, saw it wasn't returning anything...