Search results

I have the same issue, geofencing for setting flag quit working in space at some point, very frustrating for a useful feature. Was never 100% reliable, more like 90%, now it's 0%.

Typically it is AC using two diodes to allow three button over two wire. Full short is usually the main opener button, shorting just one of the phases does the other two functions(lock or light).   I use an HAI relay in parallel to the main button with NO and have a soft button setup that closes...

luping you have mentioned silencing iOS or DnD before, this is really not useful.   Remembering to DnD before opening Haiku is just not feasible, plus it it silences important things like calls and text messages, which my spouse will want to know about ;)   Haiku beeping at me while I am staring...

I would love a way to silence Haiku completely without silencing iOS as a whole.   Why do I need sounds when I am looking at the app directly?   The only use for sounds in Haiku would be if I had a iPad mounted on the wall which I don't, not counting push alerts from HH which are handled...

Odd to not have your garage doors as Entry/Exit as intended, why not have them armed with the system?   In any case, make one or two messages show and clear the message with automation when the aux zones change state, this has been what HAI has recommended for aux zones forever, that way they...

lupinglade can correct me, but from what I can tell Haiku is heavily dependent on the Apple stack (Objective-C, Cocoa) so porting to other platforms will be a large amount of work. I pleaded for a Linux version of Haiku Helper specifically for my Synology but was told to buy a Mac mini...

Do you have a message triggered off the aux zone? This has long been the recommendation from HAI if you want an aux zone to display on the keypad when not ready, this works for Haiku as well, unfortunately Haiku also ALWAYS beeps messages even if displayed with no beep, it will also push them...

The latest version of Haiku seems to have resolved the issue for me so far. 

It looks like 4 is not enough as I just got another trouble push, I will keep pushing it lower and see if they go away, I am afraid even 1 might not be enough as the voltage may be dropping to 0 for a short period sometimes.   I haven't done much HH scripting, but I do javascript in my day job...

It my limited testing setting dead line detect to 4 or below seems to stop the Haiku Helper trouble from pushing. Above that and it it consistently reproducible by calling my home line and hanging up, the trouble is pushed when the line goes back on hook. Using the test menu on the keypad it...

  Are you sure?: http://cocoontech.com/forums/topic/23030-helper-and-phone-line-disconnect-errors/

Just answer this question for me then, why does the Omni wait 60 seconds before classifying a dead line as a trouble?

Overriding EEC for testing is explained on page 8:     5. Press [HOLD] and select “On” to override Energy Efficient Control.  6. Set the Mode to "Heat". Raise the desired heat setting 1 degree above the current temperature. Ensure  that Stage 1 heat comes on. After a few minutes, raise the...

I believe the EEC tries to be more intelligent than a simple temperature difference, which is why it says to disable EEC when testing the system stages.   Here is a snip from the Omnistat installation manual:   This thermostat is equipped with Energy Efficient Control (EEC) that continually...

So I just confirmed, if I pull the line for just a few seconds Haiku Helper pushes a trouble immediately while the Omni ignores the issue until 60 seconds has elapsed before reporting trouble. I speculate the REQUEST SYSTEM TROUBLES probably returns nothing during the first 60 seconds as the...

I think you are referring to:     DEAD LINE DETECT NOTE: To disable OmniPro II from detecting a dead line, set this item to '0'; otherwise adjust only under direction of HAI. This item adjusts the threshold that is used to determine when the phone line goes dead. DEAD LINE DETECT: 8 0-15...

However as I said the trouble is never logged in the Omni event log. When I actually pulled the phone line manually the Omni logged a trouble and put it up on the keypads which stay there until it's cleared.   How is it possible to have a trouble in Haiku without it being anywhere in the Omni...

It actually just occurred again while at home, it's definitely triggered by a call and occurs at the point when the call ends.

I have started getting phone line trouble push notifications and then immediately trouble cleared randomly about once a day, sometime more than once. At first I though my FiOS line was simply having issues as losing dial tone, but looking at my Omni event log, there is no record of it there...

  Ok here is one done Sept 2012 by [email protected], is this new enough?:     http://www.itu.int/dms_pub/itu-t/oth/06/.../T065B0000320004PPTE.ppt   PON only through 2012.   More proof:  ...