I have only read the first page or two of this thread & haven't kept up with all the posts, so please pardon me if this is irrelevant at this point in the discussion. However I bumped in today in this GSM Gate Opener RTU5015 & I thought that this might be what the OP is looking for so I thought...
You can do it in BI, but they say in the help that it will increase the CPU utilization significantly and are recommending against it. They say you should rather adjust the FPS in the camera settings, which obviously makes it impossible to play & record at different FPS rates.
Hi LarryLix,
I am still new to the WC8 and I was having a hard time following your programming as it was too sophisticated for me. I am also still unsure of how the GOTO works and where it goes from there as opposed to the CALLSUB. After reviewing it for along time I think I did get an idea...
So this what I tried so far to test it:
MOD CM 5 RAM80
TSTEQ RAM80 0
ADD 1 VAR6 VAR6
So VAR6 should increase by 1 every 5 minutes. The problem that I see is that RAM80 stays 0 every 5 minutes for the entire minute which increases VAR6 by thousands. Doing this to Webset a variable on the ISY...
Hi all,
I am still pretty new to the WC8 so please excuse me if this should have been obvious. I searched the forum but couldn't come up with the answer.
I have my WC8 setup to set variables on my ISY-994 upon the digital input status changes & is working fine. I want to set up a heartbeat...
Thanks CAI_Support,
I have seen on the web people mentioning this & complaining about it, including in the Amazon reviews. But I don’t really understand what the issue is. Isn’t this what the N/O & N/C connections on the relay are for? So you can connect your wire to either one, depending...
Thank you very much Tschmidt for helping me. I will look into the various option you mentioned. I do have this 8 channel relay http://www.amazon.com/SainSmart-8-CH-8-Channel-Relay-Module/dp/B0057OC5WK which I think is what you mean with "Electromechanical relays (EMR)", so I will start with this...
Thank you all for your help,
Can you please give me a link to which optocoupler to get? As I mentioned I have very little knowledge about these electrical stuff. I thought this is just going to be plug & play, connect 8 sensors to the board, write the PLC code to update a variable on my ISY-994...
I tested again now connecting the 15 feet magnetic sensor cable to IP1 and 5V. Now I did see VAR5 increasing by 1 about every 30 seconds. That's still not acceptable. I added a second resistor between ground and IP1, then it seemed to completely stop. Though I only watched it for 2-3 minutes. Do...
Hi all,
So I went out & bought from Radio Shack resistors with the same exact specs as the one that Tschmidt linked to on ebay. (BTW the price was $1.49 for 5 pieces vs. 99 cents on ebay for 100 pieces. At least I didn’t have to wait 30 days to get it…) I took the board with me to my office...
Thanks CAI_Support for your response.
As I had mentioned before I have very little knowledge about electrical stuff. So I did some googling & read up on what a pull down resistor means & does. I am confused. From what I read on a couple of websites I understand that the pull down resistor is...
Hi all,
I am pretty new to the CAI WebControl Board though I have been following this forum for a long while.
One of my goals that I am working on is to use the board to connect 8 standard magnetic contact door sensors to the 8 digital inputs. These sensors are what’s called “closed loop”...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.