Search results

Two out of three Omnistat 2's that I have replaced due to failure, all Zigbee models, are exhibiting strange behavior. When installed, they all three worked correctly, displaying relative humidty as well as the proximity sensor working correctly. Now for some reason two of them no longer display...

Has anyone been able to source OmniStat 2s? I just had two of my Omnistats go black screen after a bad storm. I had one spare and it seems to be working fine but I still need to replace one. I doubt I'll be able to find one at this point but I have to try.   Another question - is it possible to...

I have an OmniPro II running 4.0B firmware. I am seeing several of my sensors show up incorrectly and I'm not sure why. I am using a CADDX wireless bridge to tie in a workshop to my existing home security. The battery and supervisor are both tied to separate zones and are set as auxillary. The...

After spending several days trying to get my Hikvision cameras to properly work with my OmniPro II and Haiku, I finally solved it. I thought this info might be useful to others as I have seen several related posts throughout the forums. RTSP which is the preferred protocol on Hikvision cameras...

I have a HAI Omni II with two hardwire expanders. I had some issues with one of my thermostats this weekend so I removed both expanders to troubleshoot the wiring. Once I got my thermostat working correctly, I put the expanders back on the board and booted it up. Both expanders are not showing...

I installed my TED5000 unit today and had no issues getting the Footprints application installed and working. My issue is getting HaikuHelper configured to connect to the TED. It looks simple enough but obviously I am missing something. A quick search of the forums turn up nothing, unless I...

I am replacing my HAI Omni II with a HAI Omni IIe so I will be selling my board and software. Is there a test I can run against the board to be sure all circuits are working properly?   I recall seeing something about a self test using one of the keypads. I had some issues with the phone...

From the following document: http://kb.homeauto.com/print.asp?id=0&Lang=1&SID= 1.62. Can the Backlights on the Console Keys be turned off? Question: Can the Backlights on the Console Keys be turned off? Answer: Yes, they can. To do so: 1. Simultaneously press the 4 and...

I have four distinct zones with receivers and other components in each. I also have four identical DirecTV boxes in each zone. I am using Buffalo/Xantech distribution blocks in each zone. I am using MainLobby\MLServer to control one of the zones. I want to configure MainLobby so I can control...

I have been using Main Lobby and MLServer along with an Insteon PLC to send X-10 signals to X-10 devices. This has been working fine for about a month. Tonight, it just stopped working. According to the MLServer InsteonPLC logs, the PLC is online and working. When I send a command, it appears in...

I have a single gang box that I currently have a standard toggle switch in. It controls the on/off setting of a ceiling fan\light. I also have a remote that came with the fan that controls fan speed and light dimming. I am looking for a solution that will allow me to control the on\off...

I have a HAI Omni II system. I want to find a keychain remote that will let me do three things, turn on some X-10 spot lights, open or close the garage door, and arm/disarm the HAI system. Can this be done? What equipment would I need? I am looking at the Skylink automatic garage door closer...

I have an office that I want to completely control with X-10. It has a ceiling fan with light, a lamp and under cabinet lighting. Basically, that's four loads I need to control. In the room, I only have a single gang opening. It is currently being used to enable and disable the fan/light. The...

I am looking for a recommendation. I have a home with four separate rooms that have 5.1 or better. I am using Cinemar MediaLobby on the backend. I want to find a cheap alternative touch panel for each of the four locations. I have investigated the Viewsonic Airpanel (looks good but difficult to...

I'm new to channel modulation so I have a few questions. I'm including a diagram to describe what I have currently and what I am planning to do. This is a fairly simple modulation project. In room one, I have a PC and a satellite dish. They feed the local tv by a manual AV switch. I am currently...

I am currently playing around with Homeseer and the Omni plugin. I finally have it connected and it's working ok. I would like to be able to customize the front end to suit my needs. I understand that it has a Media Lobby Plugin that I want to take a look at. Charmed Quark is out of my reach...

I would like to find an X-10 receptacle that responds to dim and bright commands. All the receptacles I have seen only respond to on and off commands.

Is there anyway to disable the keypad beep for a certain period of time? I would like to turn off the keypad beeps between the hours of 11pm and 6am, but have the beeps work all other hours of the day.

I just picked up an AuraGrid from Smart Home thinking it was a good idea but now I'm not so sure. The premise is you can send a wireless b/g signal over standard coax cable to a small passthrough antenna in each room you want wireless. According to Smart Home, it is not compatible with satellite...

Looking for some insight here. X-10 was working, now its not. I get mixed results across the board. It did work previously through PCAccess and HAI control panels. Now it will not. I can use a remote and sometimes the lights will respond, sometime they will not. I have no flourescent lighting. I...