Search results

Two out of three Omnistat 2's that I have replaced due to failure, all Zigbee models, are exhibiting strange behavior. When installed, they all three worked correctly, displaying relative humidty as well as the proximity sensor working correctly. Now for some reason two of them no longer display...

So I figured I would just add to this thread instead of creating a new once since it involves Omnistat 2s. Two out of three Omnistats that I have replaced, all Zigbee models, are exhibiting strange behavior. When installed, they all three worked correctly, displaying relative humidty as well as...

@pete_c   Thanks so much for the detailed explanations. It's good to know I have options when my Omnistat 2's expire.

I'd be interested in knowing your results. I'm using MyroHome so that's really where I want to have access to thermostats.

Has anyone been able to source OmniStat 2s? I just had two of my Omnistats go black screen after a bad storm. I had one spare and it seems to be working fine but I still need to replace one. I doubt I'll be able to find one at this point but I have to try.   Another question - is it possible to...

Just getting back around to this. I have a total of four control pads (the old in-wall style), 29 magnetic entry and window sensors, 17 glass break sensors, 9 four-wire smoke detectors, an internal and external horn sounder connected. Also an 8 port relay board, using only three of the ports. I...

I powered everything down at the panel, external battery as well. When I powered back up, everything was working correctly again. The wireless bridge that I have has the eight LEDs and the loop antenna. Is that the one that the battery supervision doesn't work on?   My question regarding the...

The only identification I can find on the wireless bridge is the faceplate which says ITI Wireless and there is a small sticker on the back that says GE Interlogix Inc. Not sure which one this is but I'm assuming the GE one. I just disconnected the battery from my panel and that eliminates the...

I have an OmniPro II running 4.0B firmware. I am seeing several of my sensors show up incorrectly and I'm not sure why. I am using a CADDX wireless bridge to tie in a workshop to my existing home security. The battery and supervisor are both tied to separate zones and are set as auxillary. The...

@chasers03,   Sorry unfortunately I don't have any knowledge of the Ring cameras. A quick search on the net really doesn't turn up much info on Ring video streams either.   @JonW,   I only have a few external cameras that monitor my home entry points. If anyone wants to spend time looking at my...

After spending several days trying to get my Hikvision cameras to properly work with my OmniPro II and Haiku, I finally solved it. I thought this info might be useful to others as I have seen several related posts throughout the forums. RTSP which is the preferred protocol on Hikvision cameras...

Got it. I missed the correct IP address at the beginning of the thread - 199.19.85.253.   Thanks.

Can someone please confirm for me that this is no longer working?   A quick nslookup of push.haikuautomation.com reveals an IP address of 205.178.189.129, though that IP address does not respond to pings. This is really unfortunate as I really depended on the push notifications. Really...

Tried setting the EOL resistors to no with no luck. Getting another RMA from Leviton and shipping the board back. 

Ok, so here is an update on where I am with this. Board is still down and not working correctly. I shipped it to Leviton for repair. The board was returned and the hardwire expanders / zones still do the same thing. The board recognizes the expanders but the zone voltage doesn't register...

I have the exact same hardware expanders. I verified my jumper cables many times as I have also done the same thing. Do you recall what menu the hard and cold reset is located in? Does this reset the board to scratch where you have to reconfigure all connectivity including serial?   One of my...

I have a HAI Omni II with two hardwire expanders. I had some issues with one of my thermostats this weekend so I removed both expanders to troubleshoot the wiring. Once I got my thermostat working correctly, I put the expanders back on the board and booted it up. Both expanders are not showing...

I'm certain over time we will see improvements in the Space interface and options. Not sure if this can be answered currently but it would be good to know if an OS update came out that required an update to either Haiku or HaikuHelper, will those products continue to be supported or has work...

I'll give it a chance but my disappointment is based on spending $30 on an app I expected to be polished to a point beyond that of Haiku. I guess I just expected different. 

I have to say I am really disappointed with this app. As a long time user of Haiku, I was really happy with the interface. I'm not quite sure where the improvements are in this app as it appears to be just interface changes and window dressing. It seems like I have to hunt to find what I am...