Search results

I have an omnipro 2 with lots of sensors attached. As each of these sensors require their own +ve and GND supplies, what I did is run a couple of wires from the omnipro 12v and ground output to a terminal block which then supplies all the attached sensors. See the picture; the top of each block...

I recently started getting a Battery Low / Trbl Now reading on my OP2 and so have swapped out the battery. The problem is that the new one is also showing a reading of 155 and a Trouble condition. What's the best way to begin troubleshooting this?

While integrating the HAI Omnipro2 and Somfy US URTS transmitter, there is very little about integrating the OP2 with the European RS485 RTS here which is much more complicated.  http://www.somfyarchitecture.co.uk/downloads/buildings/rs485rts-transmitter-18108031.pdf . The HAI documentation is...

I have posted a query several times with no response from the developer - has development and support ceased?

Has anyone out there got Haiku Helper to communicate through a serial port at all? Even the simple examples in the API documentation give me an error message 'undefined' e.g.   var port=helper.openSerialPort(controller,'/dev/cu.Repleo-CH341-00002006'); port.setDataBits(8); ----> Unhandled...

I am currently trying to build a circuit that will allow an actuator to be controlled from an HAI OP2 system. The idea is that the OP2 momentary pulse will allow a +ve voltage to go to the actuator (which has built-in limit switches). A second pulse will latch the power feed with reverse...

My problems started when I installed a new expansion enclosure - before then I had a rock-solid stable system with wireless and a single hardwire expander. I started getting intermittent 'no controller data' messages on one or the other of the consoles.    The problem now is that even when I...

Hello, I want to send RS485 messages through the OP2 but they are 20 characters long and are 8O1 rather than 8N1 so the Prolink protocol does not help. Is there a way of sending the messages using HH?

I am trying to control Somfy RTS blinds from the OP2 using this Somfy RTS485 transmitter. I can successfully send commands to them from a pc connected to the transmitter but not from the OP2.    I have set PC access with a Pro-link 4800 baud serial connection, changed the link type on the board...

System has been running fine for a while until I added buttons 9-12. They are visible in PC access (obviously I wrote them to the controller) but they are not showing either on either the consoles or in Haiku Helper.   Any suggestions?

I have a Normally Open zone that has a loop value of 137 when secure; However, it has recently started randomly dropping to 136 from time to time which puts in a Not Ready state.  I have tried replacing the limit switches and the resistors on the zone in case they were faulty, and checked the...

I am getting numerous video artifacts and intermittent connection dropping when I go to the camera page. This is with 9 cameras, all using RTSP and 30FPS so I am wondering if it is a bandwidth issue - what is the recommended number and settings for cameras? Network is gigabit with the ipad...

I cannot seem to get Haiku Helper successfully talking to an MS Exchange SMTP server. TLS is enabled, have tried different authentication mechanisms, ports 25 (with basic authentication set to occur after TLS is established) and 587 with no joy; is there a way of seeing the SMTP conversation...

Hi, I am looking for some advice regarding adding cellphone dialler backup capability to an HAI OP2. I don't want to go with the HAI C3 due to it being 2G only.   What I am looking for is something which has the capability to:   1. In the event of the hardwired phone being unavailable, take any...

Looking at HH at the moment and would like some info on how it operates -   Do Haiku and/or HH upload code to the OP2 in the same way as PC access so that it is all running on the OP2 controller and will still work fine in the event of a mac power failure (other than push alerts)?   If so, how...

Just looking at this now and trying to work out what the various options are if I want a touchscreen controller that can 'pop' the display on detection of an event.   I saw that Omnitouch 7 screens don't yet have this feature although it's been announced. Is the only option currently Omnitouch...

I am considering the email notifier board but it occurs to me that the same can be achieved with CQC although with a steeper learning curve. Given that I have an always-on server that could run CQC, is there anything I am missing here?

Am I right that you effectively get the same result with an analogue PTZ camera that offers a sufficient level of optical zoom, as a high-resolution digital camera?

Is it correct that only Somfy ILT RS-485 motors can communicate their position back to an HA system and that the RTS (wireless) and ILT dry contact motors are effectively one-way communication only?

I am trying to choose a home security CCTV solution and would welcome some input as to the best option.    There will be up to 8 outdoor cameras in locations which have up to 30m of conduit running to them, and no local power supply. I would like PTZ capability and the ability to integrate live...