Search results

I'd appreciate if anyone can provide me with a copy of the installation instructions for GE NX-482 (this is wireless motion detector). I just want to know what are the jumper settings? Thanks

What is the maximum magnetic gap for this wireless sensor

How do I manually enroll the 4-button keyfob into the ELK M1G ESPECIALLY I lost the original TX ID of the keyfob? Any help would be appreciated. Thanks

I currently have couple of rules when I arm the system in AWAY or VACATION mode it would turn the Valve OFF and when DISARM it would turn the Valve ON. Now I still want to do the same thing except how do I write rules such that the VALVE ON between 3:00-6:00 A.M because I have a lawn sprinkler...

I'd like to get assistance from anyone who can give me some guidance on the followings: I recently purchased and installed the ELK water shutoff valve and it works great. I currently have the unit wired up to OUTPUT3 of the M1, however, now I want to install a manual big push button in my...

Spanky I have a client and her house is about 9000 sqft and I need to use some wireless. My question is can you have more than one wireless receiver whether the soon to be released M1 receiver or the Caddx. If I remember correctly the current M1 can only accomodate one Caddx receiver whether...

Spanky Any latest information on the upgrade release date? Thanks

Spanky Do you have a release date for the 4.4.6? Thanks

I'd like to share some information for anyone interested in using Elk M1 via Serial Expander to Uplink AnyNet Module to NextAlarm. I recently installed and activate the Uplink AnyNet and it works great with NextAlarm. NextAlarm received full Contact ID information just like you did not lose...

I'm currently using Elk M1 and would like to find out what are added features would LeopardII provide that M1 cannot.

Currently, I'm using the Rosslare AY-G54 26 bit Weigand reader with M1, however, I have question regarding the connection for the "tamper" wire. How does this "tamper" wire is hook-up to one of the zone in the M1. The tamper wire is a single wire so how do I get the neg to connect with one of...

Has anyone use the touchscreen from ELK to control the M1? I'd like to receive some feedback either positive or negative.

I just upgraded mine to the 1.6.10 and I encountered a problem. If I selected ALL options then select print it would give me a message "run time error message 2147217887 (80040c21) multiple-step operation generated errors. check each status value". If I de-selected the RULES option then the...

Does the KP2 work with PIN reader?

Spanky I have 3 Input Zone Expanders connected to the Data Hub and when I power down the system the reading across terminals A&B is 73 ohm for each expander and the Data Hub. Is it within tolerance? Second issue. I checked the menu 8,6,1 and after a week my databus error reading is A2T4 is...

My current configuration has three (3) Input Expanders. Problem: Suddenly the Input Expander #2 loses communication with the panel and it causes alarm to all of the zones connected to Expander #2. 1. I went into ElkRP and attempted to re-enroll the module without success. 2. I then power...

I just received and installed the new keypad KP2 recessed into the wall and it works perfect. It is awesome. It's been said before built-in temp sensor would be very much desirable.

I just noticed the elk website shows arming station. Does anyone have any ideas when this product is actually is going to be available? Also, is cat5 cable required for this install?

Spanky My current configuration as follows: Spanky Control Panel: 3.1.10, 4.3.12 Keypad: 3.0.14, 2.1.44 ElkRP: 1.6.8 I also have the M1XVOR board installed previously to fire a rule to open/close my garage door. Strange problem that I obserse after I performed keypad boot and firmware are...

I attempted to perform the M1G control panel bootware/firmware and ran into problem. Not able to do it. Message something about flash not working. I called tech support and was inform to send in the panel for repair/replace Prior to upgrade I was running bootware 3.1.10 and 4.3.12.