Search results

Hello everyone. When I built our home back in 2014 I wired all doors and windows back to my OmniPro II.  Over the years I've been adding more and more devices (Lights, Outlets, etc..) to my Google home system.  All of my lighting automation and sprinkler system have been migrated off the...

Hello, When I built our house 5-6 years ago I installed the Omni Pro II in my server closet.  I was fortunate and the builder let me run all my own low voltage.  I ran at least two CAT6 drops to every room and to anywhere I might one day install some sort of display panel.  I also ran all the...

Hey guys., I have been running an Omnistat2 down stairs and a regular Honeywell upstairs with no issues. I found an Omnistat2 on ebay for $150 so I grabbed it and installed it using the same wiring configuration as downstairs, set the address to "2", and configured it in PC Access. In the...

Hello, yesterday my OmniStat2 quit working.  I just happened to have another one laying around so I plugged the face into the backplate and still nothing.   I read through the posts I could find and tried disconnecting my ethernet cable, making sure wires are secure.   Not sure what else to...

Hello, I have a two story house with a zone for upstairs and a zone for downstairs.   I purchased an OmniStat2 for downstairs and it has been working flawlessly.  It took me a few months but I finally replaced the upstairs thermostat with another Omnistat2.   I have it setup just like the one...

I have created buttons to control each Zone of my Irrigation system (Flower Garden ON, Flower Garden OFF, etc...) It works great for what I need but there has been a few times when I forgot which zone I turned on or off. Is there a way to determine which button or zone is in what state.   The...

I just purchased a OmniStat2 RC-1000 to start playing around with HVAC Automation.   I have two zones, a Thermostat upstairs and downstairs.  I am replacing the one down stairs with the Omnistat2.   Here is the original wiring   And the wiring in the garage   Here is how I have it wired to the...

I have two motion sensors connected to my OmniPro II. They are both programmed as Away-Int through PC Access.   They both started showing as NOT READY on the key pad.  First the living room then the Dining room. Nothing has changed in my environment and both Motion Detectors turn red when you...

It is finally time to connect my HVAC system to my OmniPro II.   I believe HAI recommends the OmniStat 2.  But do you guys recommend anything else etc.. Zigbee, etc...   There are currently two thermostats. One upstairs and one downstairs.  I pre-ran a CAT5 cable from each location back to the...

I currently have an OmniPro II controlling my security and Irrigation. When my budget will allow, I plan on installing 5 IP cameras, lighting control and eventually working on automation tasks.   The only input device I have hooked up is an HAI Security Keypad.   I would like to purchase a...

We have been our new house for about 6 months now. I've got my security and irrigation going through my OP II right now.   It's a little messy but this was my first install and I am always messing around with it. The cables on the right are speaker wires to each room and two CAT5 to each room...

I have an OmniPro ii that I have been using just for security.  Can't afford cameras,music,lights etc.... just yet.   I just purchased the 8 port relay board I would like to use to control my irrigation with. The wiring seems pretty easy.  But I have no experience in the programming part.   What...

Is there a way to program what zones to monitor during Night mode? It is a two story house and I do not want to include every "Exterior" door or window.  I have a balcony door upstairs that I would like to open during the night as well as the upstairs motions and windows.   Thanks Mike

Can anyone help me in wiring a 4 wire Aurora PIR to my OmniPro ii.   Thanks, Mike

I know this topic has probably been beaten to death by now but I can't seem to find what I am looking for.   We are three weeks out from moving into our new home.  I have installed an OmniPro ii.  I've got the security side configured using PC Access.   I am now trying to figure out the...

I will be using a 42" panel from Leviton.  It will house my OmniPro ii, HiFi2, Cisco 24Port POE switch.  I am sure I will add more later down the road but that should get me started.    My concern is heat.  My switches here at work produce a lot of heat that gets routed out of the rack.   I was...

We have reached the electrical part of our build. I was walking around ensuring that the electrician wired a neutral to each switch. I noticed that he had 4 wire cords labeled SMOKE throughout the house. I told him I was going to run the smokes back to my panel. He said he had to wire...

I read where I need to use 22/4 FPLR RED Cable for my smokes.  But I could of swore I read somewhere that I need to use Red cable for my keypads, I just cant find it.  Do I need to or is normal 22/4 okay to use.   Thanks Mike

There is one place on our proposed electrical plans that calls for 6 light switches.     I was planning on using HLC switches with my OmniPro ii.   I would like to be able to control those lights with a single multi-switch switch that is compatible with my OmniPro and UPB.   Any advice or...

I just received my OmniPro ii board.   The selling included some cables, a UPB Powerline Interface Mod (36A00-1), A 2 way voice module (10a11), and two RJ31X jacks.  I paid $790 for the lot but...   I think the board is missing the firmware chips.   Do I just purchase two 20A04-2UPG and install...