Good morning everyone, just to provide an update. I did purchase and install the new board. All communication issues were resolved. The system has been up and running flawlessly for several months now. Thank you for your help!
Good evening Pete, Del, and Ano,
I want to sincerely thank you for your help with this issue! I respect your knowledge and have learned an unbelievable amount from your posts on here. Unfortunately I have worked through all of the suggestions with no luck. I also received a reply to an...
Pete,
Again, thank you for your help! What I did to test the line itself is cut the end off of a telephone line, stripped the ends, and attached them on the OMNI PRO board where the incoming lines are connected. I did have a dial tone right there at the board, so I believe that...
I forgot to mention that after each EEPROM reset, the system did appear to be back to factory settings. The Installer Code is reset and none of my programming or time setting are there, so the reset appears to take effect. It does not however appear to reset the firmware revision which I am...
I want to thank everyone for their help so far, but still no luck. I have reset the system twice now. To ensure I am doing what you expect by a hard reset, on a keypad console I am going to 9-Setup, #-INST, 6-MISC, and selecting RESET SYSTEM EEPROM. On the second reset I even tried resetting...
Good afternoon,
I have had an HAI OMNI Pro II running flawlessly at my house for a couple of years now . All of a sudden I am having an issue with the Digital Communicator. The Central Station is not receiving verification from my system anymore. In testing it, it does not call out for...
I had posted a similar question recently regarding a differnt brand of glassbreaks. The following thread will provide you the answers that I got:
http://cocoontech.com/forums/topic/24811-glass-break-sensor-question/
I have to apologize. It seems like every new item I tackle has some oddity that I have to bother everyone with. Thank you for your help!
I have three HAI Wireless KeyFobs (48A00-1) which I am trying to incorporate into my OmniPro II system utilizing an HAI Wireless Receiver (45A00-1). I was...
Finally had a chance to reverse all of the Dip Switches. No luck. They appear to be right in the configuration that I had them in at first. As stated earlier, the sensors are working as they should, the only feature that I can find that is not working (of the ones that I am using) is the Walk...
tsasecurity,
I am hoping to piggy back off of your first question. I also have an HAI install (OmniPro II) and have a similar scenario. I have my house and attached garage setup as two separate Areas. I would like to have an Exit/Entry Delay in both Areas for the single door in between...
I am sure that I am just missing a simple setting somewhere, but unfortunately I have searching the installation manuals and the net for over two hours with no luck. I have created 4 Buttons on my OmniPro II setup utilizing PC Access. I gave them all Names, Descriptions, Voices, and assigned...
Some items are still high, but several are a really good deal. You have to compare item by item. I was able to pick up an HAI Camera Server for a couple of legacy cameras I have for well less than I could find it anywhere else. I ordered around midnight Wednesday night andy got it Friday, yet...
I also prefer wired sensors. Unfortunately our driveway has a loop in between the house and where I want the sensor. Without boring under the concrete I have now way to get wire to where I need.
I have made it through the night with no false alarms. These changes appear to have resolved...
Desert,
You may have found it. I unenrolled the sensor, and reenrolled in a new location (I had one blank zone before it also waiting for a future sensor). I then enrolled my keyfobs which filled the first segment of 16 zones. I removed the second segment of zones from the wireless...
Desert,
No, I actually have it set up to receive 32 zones in preparation for some additional items (keyfobs, etc.). I currently do not have anything in the second block of zones. Could this be throwing it off?
Bad news, I verified and I do not have the sensor set as supervised (the "Type" led is blinking). For clarity, I have the Mode led off for this sensor as well meaning that the sensor does not send a "Restore Transmission". So unfortunately this does not explain my consistent 69 minute...
This site uses cookies to help personalise content, tailor your experience and to keep you logged in if you register.
By continuing to use this site, you are consenting to our use of cookies.