Search results

Hello all,   Recently I no longer receive email notifications from my webcontrol boards.   Something to do with my email provider I was using on the webcontrol board changing to secure email?   Anyone else have this issue? Any email provider that still works with these boards that you can share...

Greetings all,   I have an old version of webcontrol  Version: v03.01.03 that's been working well for what I need it, basically turning my outside lights on and off from a photosensor installed outside. Also have it turn on another light based on time. Rencently the analog photosensor input is...

Hello all,   I have the following in my old Version: v03.01.03 of webcontrol.   However, it is not working. I'm trying to have the board send me one email when the humidity goes past 50%  and then another email when humidity reading goes below 45%   In red is the humidity setup, and below that...

Hello all,   I ran into an issue with receiving notification emails from my boards.   Everything was working fine for several years, but I needed to change the photo light sensor up on the roof because there was a large fluctuation in the analog input reading, and I had this problem a few yers...

Hello all,   I wanted to add additional program lines to the below code that I have in one of my older Webcontrol board. Version: v03.01.03   I tried so many different combinations but it will not work.   Basically, I wanted to add to my existing code (listed below in green) code that will tun...

http://cocoontech.com/forums/topic/24995-pull-up-resistor-wiring/   Hello All,   I accidentally posted the above questions to the wrong forum, I received some help, but not enough to fix my issue.   Basically i wanted to know how to hook up a resistor so it stops sending more than one email...

Greetings all,   I'm having a hard time wiring a pull up resistor as per the Webcontrol manual where it is mentioned to wire a 2.2k pull up resistor to fix the issue where you get multiple emails when a button is pushed.   I have two button push type inputs on my board, and when the inputs get a...

Hello all,   I purchased a keypad that I want to add outside the door. I want to be able to enter a pin code on the keypad and the signal from the keypad goes to IP2 on the board to give a signal to OP1 to trigger a relay (that I have in place and working via other cai programing)   Here is the...

Hello,   Is there any way to remotly reboot my WC board?   I'm away from the location now and the board is not responding to some commands.   This board has some issues, sometime it will lockup, and needs rebooting, sometime only certain commands do not work, and needs rebooting, like now, but...

Hello,   I'm trying to have the board send me one email when the humidity is above certain %, then send another email when it is below a certain %   Below is the complete code, Marked in RED, All other code is working fine.   The Email for Humidity, are not working.   Can someone please help me...

Hello all, Below is the logic cript I have to run lights on and off and send email alerts to me when lights come on and when lights go off. This has been working great for some time. What I wanted to add is email notification from Temperature sensor 3. Basically would like an email sent when...

Hello, Can a keypad be used with cai webcontrol? Basically what I would like is to have a keypad outside the door, if the correct code is entered on the keypad, the cai webcontrol would trip the relay and open the door. As of now I have the cai hooked up, where I can open the door via my...

Hello all, I've been using a couple Cai webcontrol boards for almost a year, to controll temperatures and lights. I have both boards setup in a way that where there is a value change, I receive an email. This has been working fine, expcept I get to many emails, and unless I save those...

Hello all, I have a Cai webcontrol board hooked up to a relay that controls my outside light. I have a photo resistor with a 1k resistor and this is what triggers the analog input set to turn the relay on and off, in turn switching the lights on and off. Everything was working perfectly up...

Hello all, I have an intercom that when someone presses my button it rings in my home. I tested the voltage and while the button is pressed it reads approximately 3.5v. If I disconnect the actual bell or buzzer and press the button it reads just under 5v. So without load it's about 5 volts...

Hello all, So I've been messing around with this webcontrol, very cool device, appears to be limitless, if you can figure out how to program it. Below is the programing for one of my devices I use control the temperature and control the front door. All works great, but would like to take it...

Hello everyone. I have a couple Cai Webcontrol boards, I use them for several things like to remotely open my front door, control lights inside via the x10 features, control lights outside via a photo resistor. I've been able to do this with the help of the great folks at CAI networks...